. RS 2000 RS 2000 Wireless TV headphones Instruction manual. Important safety instructions.3 Package contents. 6 Product overview. 7 Putting the RS 2000 into operation.9 Setting up the transmitter.9 Connecting the transmitter to an audio source.10 Connecting the transmitter to the power supply system.13 Charging the stethoset receiver’s rechargeable battery. Protect your hearing from high volume lev- els. Permanent hearing damage may occur when headphones are used at high volume levels for long periods of time.
Sennheiser headphones sound exceptionally good and provide clear speech intelligibility at low and medium volume levels. Do not operate the product near heat sources.
This manual contains important information about the installation, operation. Read and follow all warning notices and instructions accompanying this product.
Clean the product only with a soft, dry cloth. Use only attachments/accessories/spare parts supplied or rec- ommended by Sennheiser. Safety instructions for lithium polymer rechargeable batteries WARNING If abused or misused, the standard/rechargeable batteries may leak. It is considered improper use when the product is used for any appli- cation not named in the corresponding product documentation.
Sennheiser does not accept liability for damage arising from abuse or misuse of this product and its attachments/accessories. Before putting into operation, please observe the respective coun- try-specific regulations. Instruction Manual PDF file at www.sennheiser.com/download. A list of accessories can be found on the RS 2000 product page at www.sennheiser.com. For information on suppliers, contact your Sennheiser partner. To find a Sennheiser partner in your country, search at www.sennheiser.com.
Is connected to the transmitter, the rechargeable battery is almost empty.is not connected to the transmitter or cannot connect to the transmitter.is not connected to the transmitter or cannot connect to the transmitter, the rechargeable battery is almost empty. Charging contacts for Analog 3.5 mm In analog stethoset receiver with audio input (3.5 mm jack holding magnets socket), marked blue Transmitter status LED The transmitter.is in standby mode.and the stethoset receiver are connected. Putting the RS 2000 into operation Putting the RS 2000 into operation Setting up the transmitter Choose a suitable place near your sound source. Separate the transmitter from other wireless devices in the room by at least 50 cm/20' to avoid interference.
Putting the RS 2000 into operation Connecting the transmitter to an audio source You can connect the transmitter to an analog audio source (e.g. A TV or a stereo hi-fi system). You can also refer to the beginner’s video guides on how to connect your digital wireless headphone system to a TV: www.sennheiser.com/how-to-videos.
Putting the RS 2000 into operation Connection possibility A: 3.5 mm jack socket (analog) Connect the stereo audio cable to the blue Analog 3.5 mm In audio input (3.5 mm jack socket) of the transmitter and to the 3.5 mm headphone socket of your audio source. Putting the RS 2000 into operation Connection possibility B: RCA sockets (analog) Plug the RCA adapter. onto the stereo audio cable.
Connect the stereo audio cable to the blue 3.5 mm jack socket of the transmitter. Connect the RCA connectors to the RCA sockets (mostly labeled “AUDIO OUT”. Putting the RS 2000 into operation Connecting the transmitter to the power supply system Connect the connector of the power supply unit to the yellow socket of the transmitter. Select a suitable country adapter and slide it onto the power supply unit until it clicks audibly into place. Putting the RS 2000 into operation Charging the stethoset receiver’s rechargeable battery A complete charging cycle takes about 3 hours. Before using the receiver for the first time, charge its rechargeable battery for a com- plete charging cycle without interruption. Using the RS 2000 Using the RS 2000 Switching the wireless headphone system on WARNING Vol + Danger of hearing damage due to high volumes!
This stethoset receiver allows you to set higher volumes than con- ventional devices. Constant high-volume use can cause hearing Vol - damage. Using the RS 2000 Switching the wireless headphone system off Take the stethoset receiver off so that the ear bows fold inwards. The stethoset receiver automatically switches off after 3 sec- Receiver status onds. The LED goes off. The transmitter auto. If you find the ear pads uncomfortable, try other ear pads.
Ear pads in different materials and forms are avail- able as optional accessories from your Sennheiser partner. – the stethoset receiver hangs freely from your ears and rests lightly on your chest. Using the RS 2000 Adjusting the balance Balance buttons allow for left/right volume adjustment.
Adjust the balance so that you hear equally well with both ears. Press the Balance button on the right or left hand side to gradu- ally increase or reduce the volume for your right or left ear. Cleaning and maintaining the RS 2000 Cleaning and maintaining the RS 2000 CAUTION Liquids can damage the electronics of the product! Liquids entering the housing of the product can cause a short-circuit and damage the electronics. Keep all liquids far away from the product.
Sennheiser ser- vice partner. You need suitable tools for replacement. We therefore recommend to have the rechargeable battery replaced by your Sennheiser ser- vice partner.
To find a Sennheiser service partner in your country, search at www.sennheiser.com. Switch the stethoset receiver on by pulling the ear bows apart. Simultaneously press and hold the volume buttons +/. Receiver status LED quickly flashes green. Once paring is completed, the Receiver status LED and the Transmitter status LED light up green. The audio transmission starts.
If the LED on the charging adapter flashes red and green, a charging error/battery error has occurred. In this case, disconnect the charging adapter from the stethoset receiver. More information on the rechargeable battery can be found on page 20. The audio cable is not properly Check the audio plug connection. Sound only on connected. One ear Use an adapter (mono to stereo jack The TV has only a mono headphone socket) to connect the transmitter to – socket the TV. RS 2000 product page at www.sennheiser.com for the most up-to-date list of frequently asked questions.
You may also contact your local Sennheiser partner for assistance. To find a Sennheiser partner in your country, search at www.sennheiser.com. Specifications Specifications RS 2000 system Carrier frequency 2.4 to 2.4835 GHz Modulation 8-FSK Digital typ. 85 dBA at 1 V Signal-to-noise ratio RF output power max. 10 dBm Audio latency.
Pioneer Bluetooth Autoradio mit 3Zoll Display mt Freisprechanlage: Biete hier zu Kauf ein Autoradio mit Bluetooth Freisprecheinrichtung (externen Mikrofon). Kein optisches Laufwerk!!! Also absolut ohne CD Das Radio ist wenige Monate alt und kommt mit Rechnung und OVP.
Bei Verbindung mit einem Bluetooth Handy hat man den vollen Zugriff auf das Telefonbuch des Handy´s. Technische Daten: Bluetooth, externes Mikrofon, DivX Video, Speicherkartenplatz (SDKarten), USB Anschluss, mp3 Datei abspielbar, 3Zoll Display ( 7cm), ISO Stecker gerne weitere Bilder oder Fragen unter 018 oder email: [email protected] Preis: 240 EUR VB. Original VW 15 Zoll Radkappe 3BO 601 147: Angeboten wird eine Original VW 15 Zoll Radkappe Ca. 2001 VW Teilenummer 3BO 601 147 (PA 6.6 M 15.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |